Apoxie Resin for Repair or Design Work

This new brooch was so easy to make that a few of you might start rummaging in your stash drawers before you finish reading this post.

Notice how even the edges are?

The brooch was made possible because of the magic of these two little balls of Apoxie Sculpt.  Apoxie Sculpt is a two part system.  When you knead these two “clay-like” products into one solid putty you get a special clay that air dries and then cures in 24 hours.

In my collection of broken jewelery parts I had this wire and crystal heart.  (You might not notice but the heart actually snapped at the bottom.)

I rolled out my Apoxie Sculpt on a non stick surface and embedded my heart into it.  Using a blade I cut away any of the Apoxie from the edges.

Then I happily embedded my Preciosa Pointed Back crystals ab(ca#36204). I did sand my edges a little.  After the brooch completely cures, you can easily add a bar pin to the back and now this sample is  ready to wear!

Apoxie Sculpt In A Mold

Yesterday’s blog post highlighted using Apoxie Sculpt as a surface to embed crystals into.

Today I’ll show you how easy it is to create unique molded embellishments with it.  For this sample I used the Black Apoxie Sculpt, White Apoxie Sculpt John Bead also has a Apoxie Clay kit with Black, Brown, Grey and White that is a nice starter kit and is great for this project as well. I also used a handmade silver plated Metal Complex pendant bezel (36x32x2) and Preciosa Pointed Back crystals ab(ca#36204).

Whenever I work with Apoxie Sculpt I have a little bit left over.

Since I don’t want to waste one bit of Apoxie Sculpt, I started to leave a mold out on my table.  I press any leftover Apoxie Sculpt in my mold and leave it to air dry and cure for 24 hours.  I knew I wanted a black and white flower theme for my new pendant and these molded ones turned out perfect!  I did do a little filing to take off any uneven edges.

For this sample I filled my bezel with the black Apoxie Sculpt.

Then I arranged and embedded my flowers.  At this point I decided to see what else I had in my stash which would complete the black and white theme.  I found three of these vintage enamel flowers and embedded them too.

My last step was to put a small ball of black Apoxie Sculpt in the enamel flowers so that I could also add three crystals.  Now that I have worked in black and white I am excited to try all the colours in the Apoxie Clay family!

Apoxie Clay and Metal Complex Bezels

This sparkly new bracelet is so easy to make that you will want to create more than one at a time!

Bezel ring blanks provide you with an endless opportunity to show off your favorite crystals.  This ring is my new favorite.


These projects were created with two new products at John Bead:  The Apoxie Sculpt Modeling Compound (available in many colours, I used Black Apoxie Clay ) and the new line of bezels called Metal Complex.  I chose the handmade oval antique brass ring for this first project.

The crystals I used were all Preciosa Pointed back Chatons and Cushion Back Chatons in various shapes. I used a Jet Navette 8×4 mm, a Pear shaped Black Diamond 8x4mm and a Crystal Chaton  .  I selected a group of my favorites and did a little sample design on my table.

The Apoxie Sculpt is a two part clay-like system.  You mix two equal amounts for two minutes until the final colour is uniform.  This “clay” now has a working time of 1-3 hours and then it air dries rock solid!

I filled the bezel ring with Apoxie Sculpt.  The left-over clay I set aside.  (I’ll show you tomorrow what I did with my leftovers.)

Then I carefully pressed all my crystals into the clay.  At this stage I added a few impressions to the clay by poking into it with a tooth pick.  All I had to do now was wait for the clay to cure for 24 hours.  Project complete!  The crystals are permanently affixed with very little work on my part.

Since I had everything out on my table I thought it would be fun to try a second bezel.

These handmade interchangeable silver plated bezels links are perfect for quick projects.  I played with these aquamarine navette crystals until my flower idea was in a design format I could reproduce in the clay.

This time I made up a small amount of the Apoxie Sculpt in Super White.  I embedded all the crystals per my design idea.  I left a few crystals hanging a bit over the edges.  I wanted the flowers to look like they were growing out of the bezel.

I could have allowed the white clay to be visible but I wanted to test another idea.  I had these tiny silver glass beads on my table and decided to see if they would adhere to the clay in the open spaces.

As you can see from the final picture the little glass beads filled in the whole background.  I also used Preciosa crystal chatons for the flower centre and on the edges.

Crystal flower jewelery in minutes!  I look forward to showing you more ideas for working with Apoxie Sculpt, Metal Complex Bezels and Preciosa crystals tomorrow.